- 标题
- 摘要
- 关键词
- 实验方案
- 产品
过滤筛选
- 2019
- polycrystalline ferrite-garnet
- magnetoplasmonic crystals
- magnetooptical effects
- deposition
- ion-beam methods
- sputtering
- plasmon resonance
- Physics
- Moscow Technological University
- Moscow State University
-
Interface characterization and mechanical properties of dual beam laser welding-brazing Al/steel dissimilar metals
摘要： The DP590 steel to AA7075 Al-alloy with lap configuration is successfully joined by dual beam laser welding-brazing without using filler metal. Through the introduction of the derived laser beam, the wetting angle, wetting distance and the thickness of intermetallic compound (IMC) layer are well improved and controlled. It is found that the wettability of liquid Al on steel improves with the increase of laser power, i.e. the wetting angle decreasing from 25.3° to 17.8° and the wetting distance increasing from 2.17 mm to 3.19 mm as the laser power increasing from 1.0 kW to 1.6 kW. Two kinds of IMC exist at brazing interface, one is η-phase (Fe2Al5) with flatten morphology closing to the steel side and the other is θ-phase (FeAl3) with needle-like morphology adjacent to the welding-brazing seam. The thickness of IMC layer increases from 8.37 μm to 12.12 μm with increasing laser power from 1.0 kW to 1.6 kW. Tensile test shows that both the wettability and the IMC thickness have influence on the welding-brazing joint strength. Poor wettability and too thick IMC layer will result in lower strength and fracture occurred in brazing interface. The optimal joint tensile strength of 123.7 MPa on average is achieved with the laser power of 1.4 kW.
关键词： Tensile strength,Welding-brazing,IMC,Dual beam laser,Al/steel dissimilar metals
更新于2025-11-28 14:24:20
-
[IEEE 2018 Asia Communications and Photonics Conference (ACP) - Hangzhou, China (2018.10.26-2018.10.29)] 2018 Asia Communications and Photonics Conference (ACP) - Cylindrical Vector Beam Fibre Laser Based on photonic lantern
摘要： We demonstrate a linear-cavity continuous-wave (CW) fibre laser generating cylindrical vector beams (CVBs) using a photonic lantern as transverse mode converter and mode splitter. The CVB fibre laser operates at a center wavelength of 1553.1 nm, with a 3 dB linewidth of less than 0.08 nm and a signal-to-background ratio of > 45 dB. The measured purity of the radially and azimuthally polarized beams is > 96%.
关键词： continuous-wave,Cylindrical Vector Beam,photonic lantern
更新于2025-11-28 14:24:03
-
Site-controlled formation of single Si nanocrystals in a buried SiO <sub/>2</sub> matrix using ion beam mixing
摘要： For future nanoelectronic devices – such as room-temperature single electron transistors – the site-controlled formation of single Si nanocrystals (NCs) is a crucial prerequisite. Here, we report an approach to fabricate single Si NCs via medium-energy Si+ or Ne+ ion beam mixing of Si into a buried SiO2 layer followed by thermally activated phase separation. Binary collision approximation and kinetic Monte Carlo methods are conducted to gain atomistic insight into the influence of relevant experimental parameters on the Si NC formation process. Energy-filtered transmission electron microscopy is performed to obtain quantitative values on the Si NC size and distribution in dependence of the layer stack geometry, ion fluence and thermal budget. Employing a focused Ne+ beam from a helium ion microscope, we demonstrate site-controlled self-assembly of single Si NCs. Line irradiation with a fluence of 3000 Ne+/nm2 and a line width of 4 nm leads to the formation of a chain of Si NCs, and a single NC with 2.2 nm diameter is subsequently isolated and visualized in a few nanometer thin lamella prepared by a focused ion beam (FIB). The Si NC is centered between the SiO2 layers and perpendicular to the incident Ne+ beam.
关键词： phase separation,Monte Carlo simulations,single electron transistor,ion beam mixing,helium ion microscopy
更新于2025-11-21 11:20:48
-
Probing the light hole / heavy hole switching with correlated magneto-optical spectroscopy and chemical analysis on a single quantum dot
摘要： A whole series of complementary studies have been performed on the same, single nanowire containing a quantum dot: cathodoluminescence spectroscopy and imaging, micro-photoluminescence spectroscopy under magnetic field and as a function of temperature, and energy-dispersive X-ray spectrometry and imaging. The ZnTe nanowire was deposited on a Si3N4 membrane with Ti/Al patterns. The complete set of data shows that the CdTe quantum dot features the heavy-hole state as a ground state, although the compressive mismatch strain promotes a light-hole ground state as soon as the aspect ratio is larger than unity (elongated dot). A numerical calculation of the whole structure shows that the transition from the heavy-hole to the light-hole configuration is pushed toward values of the aspect ratio much larger than unity by the presence of a (Zn,Mg)Te shell, and that the effect is further enhanced by a small valence band offset between the semiconductors in the dot and around it.
关键词： molecular beam epitaxy,optical spectroscopy,EDX,semiconductors,cathodoluminescence,quantum dot,nanowires
更新于2025-11-21 11:20:48
-
Possibilities of Dry and Lubricated Friction Modification Enabled by Different Ultrashort Laser-Based Surface Structuring Methods
摘要： In this contribution we report on the possibilities of dry and lubricated friction modification introduced by different laser surface texturing methods. We compare the potential of Laser-Induced Periodic Surface Structures and Laser Beam Interference Ablation on 100Cr6 steel in a linear reciprocating ball-on-disc configuration using 100Cr6 steel and tungsten carbide balls with load forces between 50 mN and 1000 mN. For dry friction, we find a possibility to reduce the coefficient of friction and we observe a pronounced direction dependency for surfaces fabricated by Laser Beam Interference Ablation. Furthermore, Laser-Induced Periodic Surface Structures result in a load-dependent friction reduction for lubricated linear reciprocating movements. This work helps to identify the modification behaviour of laser generated micro structures with feature sizes of approximately 1 μm and reveals new possibilities for surface engineering
关键词： lubricated friction,smart surfaces,laser surface texturing,laser beam interference ablation,laser-induced periodic surface structures,dry friction
更新于2025-11-21 11:18:25
-
Tailored focal beam shaping and its application in laser material processing
摘要： Besides the optimization of the laser and processing parameters, the adaptation of the focal intensity distribution offers great potential for a well-defined control of laser processing and for improving the processing results. In this paper, different tailored intensity distributions were discussed with respect to their suitability for femtosecond laser material processing on the micro- and nanoscale such as cutting, marking, and the generation of laser-induced periodic surface structures. It was shown by means of laser processing of stainless steel that the numerical simulations for the beam shaping unit are in good agreement with the experimental results. Also, the suitability of the beam shaping device to work with a scanner and an F-theta lens as commonly used for material processing was demonstrated. In this context, the improvement of the machining results was shown experimentally, and a significant reduction of the machining time was achieved.
关键词： laser-induced periodic surface structures,donut,femtosecond laser processing,top-hat,beam shaping
更新于2025-11-21 11:01:37
-
Ferroelectric Enhanced Performance of a GeSn/Ge Dual-Nanowire Photodetector
摘要： GeSn offers a reduced bandgap than Ge and has been utilized in Si-based infrared photodetectors with extended cutoff wavelength. However, traditional GeSn/Ge heterostructure usually consists defects like misfit dislocations due to the lattice mismatch issue. The defects with the large feature size of photodetector fabricated on bulk GeSn/Ge heterostructure induces considerable dark current. Here, we demonstrate a flexible GeSn/Ge dual-nanowire (NW) structure, in which the strain relaxation is achieved by the elastic deformation without introducing defects and the feature dimension is naturally at nanoscale. Photodetector with low dark current can be built on GeSn/Ge dual-NW, which exhibits an extended detection wavelength beyond 2 μm and the enhanced responsivity compared to Ge NW. Moreover, the dark current can be further suppressed by the depletion effect from ferroelectric polymer side gate. Our work suggests the flexible GeSn/Ge dual-NW may open an avenue for Si-compatible optoelectronic circuits operating in the short-wavelength infrared range.
关键词： Nanowire,Germanium-tin,Molecular beam epitaxy (MBE),Side-gated,Photodetector,Ferroelectrical polymer
更新于2025-11-21 11:01:37
-
Effect of electron beam irradiation on structure, morphology, and optical properties of PVDF-HFP/PEO blend polymer electrolyte films
摘要： The effect of 8 MeV energy electron beam (EB) on poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP)/poly-ethylene oxide (PEO) (@ w/w 90:10, PHP10) polymer blend films have been prepared and studied. The change in structure, morphology, and optical properties at 40, 80, and 120 kGy EB doses were investigated. The effect of the radiation process may responsible to occurs the degradation (chain scission) and chain link (cross linking) which are confirmed by the FT-IR analysis. The band at 1401 cm?1 corresponding to the –CH2– bending or scission mode have shifted to 1397 cm?1 after 120 kGy EB dose is due to the intermolecular interaction and the changes of the macromolecular chain by breaking of bonds with increased EB dose was observed. The XRD pattern shows decreased in the crystallinity from 60.03 to 23.42% and increased amorphousity for 120 kGy EB dose the and the surface morphology was drastically changed by decreasing the size of spherulites upon increased EB dose. The increase in optical absorption and the shifting of wavelength toward a higher end (red shift) was observed after the irradiation. The energy band gaps (Eg), and Urbach energy were estimated and they are found to be decreased, but the number of carbon atoms in a cluster of was increased with increased EB dose. The obtained results notice that the physical properties of polymer blend electrolytes can be improved by EB irradiation to use in different potential applications.
关键词： Polymer electrolyte,FESEM,UV–visible spectroscopy,Structural analysis,Electron beam irradiation
更新于2025-11-21 11:01:37
-
Study of (AgxCu1a??x)2ZnSn(S,Se)4 monograins synthesized by molten salt method for solar cell applications
摘要： The open circuit voltage (VOC) deficit of Cu2ZnSn(S,Se)4 (CZTSSe) kesterite solar cells is higher than that of the closely related Cu(InGa)Se2 solar cells. One of the most promising strategies to overcome the large VOC deficit of kesterite solar cells is by reducing the recombination losses through appropriate cation substitution. In fact, replacing totally or partially Zn or Cu by an element with larger covalent radius one can significantly reduce the concentration of I–II antisite defects in the bulk. In this study, an investigation of the impact of partial substitution of Cu by Ag in CZTSSe solid solution monograins is presented. A detailed photoluminescence study is conducted on Ag-incorporated CZTSSe monograins and a radiative recombination model is proposed. The composition and structural quality of the monograins in dependence of the added Ag amount are characterized using Energy Dispersive X-ray Spectroscopy and X-Ray Diffraction method, respectively. The Ag-incorporated CZTSSe monograin solar cells are characterized by temperature dependent current-voltage and electron beam induced current methods. It was found, that low Ag contents (x ≤ 0.02) in CZTSSe lead to higher solar cell device efficiencies.
关键词： Copper zinc tin sulfur selenide,Monograins,Electron beam induced current,Photoluminescence,Kesterite,Cations substituation
更新于2025-11-21 10:59:37
-
Assessment of Bulk and Interface Quality for Liquid Phase Crystallized Silicon on Glass
摘要： This paper reports on the electrical quality of liquid phase crystallized silicon (LPC-Si) on glass for thin-film solar cell applications. Spatially resolved methods such as light beam induced current (LBIC), microwave photoconductance decay (MWPCD) mapping, and electron backscatter diffraction were used to access the overall material quality, intra-grain quality, surface passivation, and grain boundary (GB) properties. LBIC line scans across GBs were fitted with a model to characterize the recombination behavior of GBs. According to MWPCD measurement, intra-grain bulk carrier lifetimes were estimated to be larger than 4.5 μs for n-type LPC-Si with a doping concentration in the order of 1016 cm?3. Low-angle GBs were found to be strongly recombination active and identified as highly defect-rich regions which spatially extend over a range of 40–60 μm and show a diffusion length of 0.4 μm. Based on absorber quality characterization, the influence of intra-grain quality, heterojunction interface, and GBs/dislocations on the cell performance were separately clarified based on two-dimensional (2-D)-device simulation and a diode model. High back surface recombination velocities of several 105 cm/s are needed to get the best match between simulated and measured open circuit voltage (Voc), indicating back surface passivation problem. The results showed that Voc losses are not only because of poor back surface passivation but also because of crystal defects such as GBs and dislocation.
关键词： Bulk lifetime,heterojunction,grain boundaries (GBs),two-dimensional (2-D)-device simulation,liquid phase crystallized silicon (LPC-Si),light beam induced current (LBIC)
更新于2025-11-14 15:25:21