- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Investigation of strengthening mechanism of commercially pure titanium joints fabricated by autogenously laser beam welding and laser-MIG hybrid welding processes
摘要： In this study, in order to achieve a better understanding of the strengthening mechanism in the commercially pure (CP) Ti welds, autogenously laser beam and laser-MIG hybrid welding of 4.2 mm thick CP-Ti plates were performed and the correlation between microstructure, texture distribution and the mechanical properties were systematically investigated. Microstructural coarsening and increase in microhardness were observed in the HAZ and WZ. The tensile test results suggested the base metal was the weak point of the joint for both welding conditions. The EBSD observations confirmed that a large number of 1012 and 1122 twin grains occurred in the HAZ and WZ of both welded joints, while a higher concentration of these twin grains were found in the laser-MIG hybrid joints. High concentration of the twin grain boundaries can act as barrier to stop dislocation slip during deformation and therefore contribute to the strengthening of the welds. The existence of very small twin grains and acicular α phase in HAZ and WZ would equivalently reduce the averaged grain size and therefore induce an increase in strength based on Hall-Petch’s law. In addition, the averaged Schmid factor of BM is higher than that of the WZ and HAZ in both welding joints suggesting that the grain boundary sliding will take place preferably in BM during deformation so that the necking and fracture occurred in base metal during tensile tests of both welding joint specimens.
关键词： Texture,Mechanical property,Laser-MIG hybrid welding,Strengthening mechanism,Commercially pure titanium,Laser beam welding,Microstructure
更新于2025-11-28 14:24:20
-
Microstructure and properties of high strength and high conductivity Cu-Cr alloy components fabricated by high power selective laser melting
摘要： Although different kinds of metal materials have been built in the past years, it is difficult to fabricate the components of copper alloys with high strength and high conductivity due to their high reflectivity and thermal conductivity. In this paper, Cu-Cr alloy with high strength and high conductivity was successfully manufactured by high laser power selective laser melting. The microstructure, mechanical properties and conductivity were studied and compared before and after the heat treatment. The microstructure of the as-built sample was columnar grains with very fine cellular sub-structures and precipitates of Cr and Cr2O3. After heat treatment, the Cr particles precipitated from Cu matrix, resulting in simultaneous increase in strength and conductivity. The ultimate tensile strength of 468 MPa, yield strength of 377.33 MPa, and electrical conductivity of 98.31% IACS were achieved, which is even better than the samples fabricated by rolling with post heat treatment.
关键词： Cu-Cr alloy,Electronic conductivity,Laser processing,Microstructure,Mechanical properties
更新于2025-11-28 14:24:20
-
Effects of Substrate Preheating Temperatures on the Microstructure, Properties, and Residual Stress of 12CrNi2 Prepared by Laser Cladding Deposition Technique
摘要： The 12CrNi2 alloy steel powder studied in the present paper is mainly used to manufacture camshafts for nuclear power emergency diesel engines. Laser cladding deposition is of great signi?cance for the manufacture of nuclear power emergency diesel camshafts, which has the advantages of reducing material cost and shortening the manufacturing cycle. However, due to the extremely uneven heating of the components during the deposition process, a complex residual stress ?eld occurs, resulting in crack defects and residual deformation of the components. In the present paper, 12CrNi2 bulk specimens were prepared on the Q460E high-strength structural steel substrate at different preheating temperatures by laser cladding deposition technique, and a ?nite element residual stress analysis model was established to investigate the effects of different preheating temperatures on the microstructure, properties, and residual stress of the specimens. The results of the experiments and ?nite element simulations show that with the increase of preheating temperature, the content of martensite/bainite in the deposited layer decreases, and the ferrite content increases. The proper preheating temperature (150 ?C) has good mechanical properties. The residual stress on the surface of each specimen decreases with the increase of the preheating temperature. The longitudinal stress is greater at the rear-end deposition part, and the lateral residual stress is greater on both sides along the scanning direction.
关键词： substrate preheating,12CrNi2 alloy steel powder,residual stress,laser cladding deposition,microstructure and properties
更新于2025-11-28 14:24:20
-
Effect of beam wobbling on laser welding of aluminum and magnesium alloy with nickel interlayer
摘要： The influence of conventional laser keyhole welding and beam wobbling was evaluated at two weld travel speeds and power settings. Fracture in linear lap welds would occur during specimen preparation due to the presence of Al-rich brittle fusion zone, unless one utilizes a circular laser wobbling path (at 1000 Hz). Wobbling provided better integrity due to the presence of a Mg-rich ductile fusion zone and a larger bonded width. It can be concluded that laser beam wobbling enhances joint quality by widening the joint area and mitigating formation of brittle secondary phases at the joint fusion zone.
关键词： Aluminum,Magnesium,Interlayer,Laser welding,Beam wobbling,Microstructure
更新于2025-11-28 14:24:20
-
Numerical and experimental investigation on microstructure and residual stress of multi-pass hybrid laser-arc welded 316L steel
摘要： In multi-layer welding, the interaction between the weld beads had a great impact on the performance of the overall joint. Therefore, experimental research and thermal-plastic analysis of 316L stainless steel multi-layer hybrid laser-arc welding were performed. The reasonable heat sources were proposed to simulate hybrid laser-arc welding (HLAW) and laser beam welding (LBW). The simulation results of temperature field and residual stress distribution were both validated and in accordance with experimental measurements. On this basis, Combining the simulated results with the metallurgical analysis, the microstructure of multi-layer weld was divided according to temperature histories. The formation mechanism of feathery ferrite precipitated in the re-melting zone (RZ) was analyzed. The feathery ferrite could increase the micro-hardness of the interlaminar position of weld. Moreover, the residual stress along the multi-layer weld thickness direction was simulated and X-ray diffraction (XRD) measured, which indirectly demonstrated the size and orientation variation of the grains in the RZ.
关键词： Residual stress,Microstructure,FE analysis,Hybrid laser-arc welding
更新于2025-11-28 14:24:20
-
Characteristics of multi-pass narrow-gap laser welding of D406A ultra-high strength steel
摘要： A universal and applicable method to predict bonding quality in narrow-gap laser beam filler wire welding of D406A ultra-high strength steel was presented. Defect-free joint could be achieved under the predicted optimal welding condition, while the production efficiency of narrow-gap laser beam filler wire welding under optimized welding condition was about 3.75 times that of traditional tungsten arc welding currently used in practical industry. Compared with the tungsten arc welding joint, microstructure in the fusion zone of laser welded joint was more uniform, which brought out a less fluctuation in the microhardness of fusion zone along the thickness direction. The tensile strength of as-welded laser welding joint was slightly higher than that of as-welded tungsten arc welding joint while the elongation of the former increased by 15.9% over that of the latter. A binocular stereo three-dimensional scanning method was adopted to compare the residual distortion of D406A joints between laser welding and tungsten arc welding. Notably, the distortion of laser welded joint was about 21% of that of the tungsten arc welding joint. Narrow-gap laser filler wire welding is a feasible substitute for conventional tungsten arc welding in the fabrication of welded construction of D406A steel.
关键词： ultra-high strength steel,welding distortion,filler wire,narrow-gap laser beam welding,microstructure
更新于2025-11-28 14:24:20
-
Analysis of properties laser welded RAK 40/70 steel sheets
摘要： Both, the ecological production and operation of vehicles demand using such materials for deformation zones’ structural parts, which show some specific properties and use innovative technologies to process them. Specific requirements for functionality (strength, stiffness, deformation work, fatigue properties) are closely linked to processability (formability). In the paper are presented results for multiphase TRIP steel RAK40/70 when welded by pulse solid-state fiber laser YLS-5000. Based on microstructure analysis in the fusion zone and heat affected zone the welding parameters were optimised. The influence of laser welding on the strength and deformation properties was verified by characteristics of strength, stiffness and deformation work, as they were calculated from mechanical properties measured by tensile test and three-point bending test. The knowledge gathered in the field of laser welding influence on the strength and deformation properties of multiphase TRIP steel RAK40/70 should help designers when design the lightweight structural parts of the car body.
关键词： mechanical properties,TRIP steel,RAK 40/70,microstructure,laser welding
更新于2025-11-28 14:24:20
-
Epitaxy and new stray grain formation mechanism during epitaxial laser melting deposition of Inconel 718 on directionally solidified nickel-based superalloys
摘要： The epitaxy behavior and stray grains (SGs) formation in the deposit during epitaxial laser melting deposition (E-LMD) of directionally solidified (DS) superalloys were investigated. Columnar dendritic structures were obtained by epitaxial solidification on the DS substrate. The deposit also remained the orientation of the substrate. The SGs at the fusion interface, which were hardly eliminated, were attributed to different SGs formation mechanisms. The SGs were divided into GB-SGs and MC-SGs by the distribution characteristics. The GB-SGs at the low-angle and high-angle grain boundaries with a new mechanism of dynamic recrystallization induced by accumulation of thermal strain and stress under repeated spatially variable heating and cooling. The MC-SGs around the carbides were related to the misoriented cellular crystal formation caused by the varied shape of the solid-liquid interface. The columnar to equiaxed transition (CET) was another mechanism of MC-SGs formation.
关键词： Stray grain,Nickel superalloys,Laser metal deposition,Recrystallization,Dynamic,Epitaxy,Microstructure
更新于2025-11-28 14:24:20
-
Laser welding of AZ31B magnesium alloy with beam oscillation
摘要： Circular beam oscillation was introduced to laser welding of 2 mm-thick AZ31 magnesium alloy. The appearance, microstructure and tensile properties of the welds were investigated. It was found that the low frequency about 50 Hz and the small radius about 0.5 mm are more beneficial to improve the weld appearance, under the given parameters of laser power 2 kW, welding speed 2 m/min and beam oscillating diameter 0.35 mm. The undercut defect and even the totally collapse of the weld appear when employing the frequency higher than 75 Hz or the radius larger than 1.5 mm. The microstructure evolution mainly reflects in the variation of the proportions of the equiaxed zone (PEZ) and the average grain size (SG). The PEZ decreases from 85% to 42% with the beam oscillating frequency increasing from 25 Hz to 100 Hz, while the SG reaches the maximum of 37.5 μm at 75 Hz. The PEZ decreases and the SG increases with the increase of beam oscillating radius. The results showed that the tensile strength and elongation are closely related to the PEZ, the SG and the twins. According to the experimental results, the relationship of oscillating parameters, microstructure, and tensile properties was established.
关键词： Laser oscillating welding,Magnesium alloy,Microstructure,Tensile properties
更新于2025-11-28 14:24:20
-
Microstructural Characteristics of Laser Metal Deposited Magnesium Alloy AZ31
摘要： Up to now, only a limited amount of metallic materials is investigated for laser additive manufacturing (LAM). However, the demand to widen the application possibilities by enlarging the range of materials for LAM is growing fast. By now, titanium and aluminium alloys are in the focus of research. In contrast, magnesium alloys are rarely used in the field of additive manufacturing, although they possess a low density in combination with a high specific strength. Currently, magnesium structures are mainly produced by casting but during the last years, the use of wrought alloys also increased. A reason for the rare use of magnesium alloys for LAM technologies might be the high flammability of magnesium powders. This difficulty can be avoided by using magnesium wire for laser metal deposition (LMD). In the present study, the microstructural characteristics of a LMD processed AZ31 magnesium alloy are investigated. For this purpose, optical microscopy and scanning electron microscopy were used. With the help of EDX and EBSD analysis, a change of the chemical composition and micro texture with structure height was identified. The relationship of microstructure and local mechanical properties was investigated with the help of Vickers micro hardness testing. Based on the obtained results it can be concluded that the microstructural characteristics of laser additive manufactured magnesium alloys differ from those of titanium and aluminium alloys. Thus, a wider application spectrum of LMD and magnesium alloys can be opened up.
关键词： laser metal deposition,local mechanical properties,microstructure,magnesium alloy,wire,microtexture
更新于2025-11-28 14:24:20