- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
L-Band Efficient Dissipative Soliton Erbium-Doped Fiber Laser with a Pulse Energy of 6.15 nJ and 3 dB Bandwidth of 47.8 nm
摘要： Here, an efficient dissipative soliton mode-locked fiber laser in the L-band using nonlinear polarization rotation technology is demonstrated. With a maximum pump power of 495.3 mW and polarization state optimization, the fiber laser delivers a maximum output power of 68.6 mW with an 11.16 MHz repetition rate and a corresponding single pulse energy of 6.15 nJ. The dissipative soliton spectrum is centered at 1599.6 nm with a 3 dB bandwidth of 47.8 nm. The full width at half maximum of the compressed pulse is 156 fs. To the best of our knowledge, this is the highest single pulse energy reported so far for an L-band passively mode-locked all-fiber laser.
关键词： mode-locked fiber laser,Erbium-doped fiber,dissipative soliton,L-band
更新于2025-11-28 14:24:03
-
C-band tunable performance of passively Q-switched erbium-doped fiber laser using Tin(IV) oxide as a saturable absorber
摘要： We report on the detailed study of wavelength tunability of passively Q-switched erbium doped fiber laser using Tin(IV) Oxide (SnO2) as saturable absorber (SA). As a typical n-type semiconductor, SnO2 has been widely used in gas sensors, oxidation catalyst, transparent conductor, and electrode materials in solar cell. Herein, we fabricated saturable absorber by compositing SnO2 nanoparticle with polyvinyl alcohol (PVA). The SnO2-SA is incorporated in the laser cavity by sandwiching it between two fiber ferrules. Q-switched laser operation can be continuously tuned from 1521 to 1565 nm, with a wavelength tuning range of up to 45 nm, covering almost the entire C-band. Q-switched pulse parameters such as repetition rate, average power, pulse width, pulse energy, and peak power at different wavelengths were studied in detail. Our experimental results suggest that the SnO2-SA is a suitable and cost-effective solution for broadband tunable laser applications with relatively simple fabrication process.
关键词： Tunability,C-band,Q-switch EDFL,SnO2
更新于2025-11-28 14:24:03
-
Temperature fiber sensor based on single longitudinal mode fiber laser in 2?μm band with Sagnac interferometer
摘要： A single longitudinal mode (SLM) ?ber laser with a ring cavity based on Sagnac interferometer (SI) for temperature sensing in the 2-μm band is proposed and demonstrated. The simulation and experimental results show that the transmission spectrum of the SI ?lter is sensitive to temperature change. Based on this distinguishing feature, the correlation between the laser wavelength drift and temperature variation can be established. Experimental results show that the proposed laser operates stably at the resonant wavelength of 1988.21 nm and the optical signal-to-noise ratio is approximately 55 dB at ambient temperature. Through continuous measurement for 100 min, the ?uctuation of the output laser power is lower than 0.74 dB, and the resonant wavelength shift is less than the minimum resolution of the spectrometer of 0.05 nm. This indicates that it has good stability for a certain period of time. At the same time, the laser operates stably in SLM state. A temperature sensitivity of 2.09 nm/°C is obtained in experiment. Notably, the proposed ?ber laser sensor possesses the merits including high sensitivity, low cost and simple structure, which are bene?cial to its practical application.
关键词： Fiber optics sensors,Temperature measurement,Sagnac interferometer,Fiber laser,2-μm band
更新于2025-11-28 14:23:57
-
Demonstration of linewidth measurement based on phase noise analysis for a single frequency fiber laser in the 2 <i>μ</i> m band
摘要： Linewidth measurement based on phase noise analysis using a 3 × 3 coupler has been applied in the 1550 nm band. One of the obvious advantages of this method compared with the common delayed self-heterodyne method is the low loss caused by the short delay line used. Taking full advantage of this particular characteristic, the linewidth of the single frequency (SF) fiber laser in the 2 μm band can also be measured. However, a specifically experimental demonstration of this method in the 2 μm band is absent to date. In this paper, a high-performance SF thulium-doped fiber laser (TDFL) was proposed and employed for the demonstration. The TDFL operates at the center wavelength of 1942.03 nm with high stability. By means of the phase noise analysis-based linewidth measurement system with a fiber delay line of only 50 m, the linewidth of the proposed TDFL is successfully measured. When the measuring time is 0.001 s, the linewidth is ~47 kHz. Furthermore, the noise characteristics of the SF laser were simultaneously studied by this method.
关键词： 2 μm band,phase noise,single frequency fiber laser,linewidth measurement
更新于2025-11-28 14:23:57
-
Application of MoWS2-rGO/PVA thin film as all-fiber pulse and amplitude modulators in the O-band region
摘要： In this work, a MoWS2-rGO/PVA thin film is fabricated and its applications as in amplitude modulation are demonstrated. Embedded in a praseodymium fluoride fiber laser cavity, the MoWS2-rGO/PVA thin film is able to induce pulsing in the laser output, which operates in the O-band region. As an optical amplitude modulator, the MoWS2-rGO/PVA thin film is capable of achieving a modulation efficiency of 0.17 dB/mW in the O-band region over a pump power range of 46.0 mW to 78.5 mW. C-band and L-band operation is also demonstrated, with modulation efficiencies of 0.30 dB/mW and 0.15 dB/mW, respectively over pump power ranges of 3.51 mW–52.17 mW and 24.4 mW–61.3 mW. This work can be improved by further engineering the composition ratio of the alloy material to enhance the modulation efficiency for both pulsed and amplitude modulations, giving rise to various applications, in particular in bio-medicine and manufacturing.
关键词： Amplitude modulator,MoWS2-rGO/PVA thin film,Pulse modulator,O-band
更新于2025-11-28 14:23:57
-
Temperature-dependent photoluminescence of pure and Mn-doped CsPbCl3 nanocrystals
摘要： Temperature-dependent photoluminescence (PL) properties of Mn-doped CsPbCl3 nanocrystals (NCs) are studied and compared with pure CsPbCl3 NCs by use of steady-state and time-resolved PL spectroscopies. The intrinsic exciton PL of the CsPbCl3 NCs locates at the wavelength range from 405 to 410 nm. The PL intensity in this range decreases rapidly, and the bandgap and linewidth become wider with rising temperature from 78 to 350 K. It is found that the exciton PL shows biexponential kinetics. The short-lived emission is ascribed to the surface trapping state recombination in NCs that has a photoinduced trapped pathway and a temporally resolved peak shift. The long-lived component is due to the band-edge excitonic recombination. Mn dopant open a new emission window at the wavelength range from 560 to 680 nm, of which intensity increases from 140 to 270 K, and then decreases with rising temperature up to 350 K. This unusual temperature dependence is ascribed to the thermal-assisted transition from the excitonic state of NCs to the 4T1 energy level of Mn2+. This work shows the potential of transition metal element doped perovskite NCs that can take advantage of the coupling between excitons and the d electrons of the dopants for expanded functionalities, such as temperature sensor and light-emitting diode.
关键词： Photoluminescence,Band-edge exciton,CsPbCl3,Mn-doped,Nanocrystals
更新于2025-11-25 10:30:42
-
Determination of nanoscale titanium oxide thin film phase composition using X-ray photoelectron spectroscopy valence band analysis
摘要： The phase compositions of nanoscale thick titania films on the titanium were determined using X-ray photoelectron spectroscopy valence band analysis for the first time, by deconvoluting the two-peak structure of valence band into five peaks and analysing the relative peak area. The titania films of thickness varying from about 2 nm to 8 μm were obtained by the air oxidation of commercially pure titanium at different temperatures. The titania films formed on titanium for oxidizing temperatures up to 200 °C were amorphous, with thickness < 10 nm. The sub-stoichiometric oxides present at the TiO2-Ti interface were composed of Ti3+, Ti2+ and Ti1+ states when the film of thickness was < 10 nm. At 300 °C, when the titania film thickness was < 20 nm, it was fully converted to rutile phase and remained stable up to 1000 °C. A broadening of full-width half-maxima of the core level peaks for the titania layers was attributed to the presence of surface hydroxyl group and stress gradient within the oxide layer. The absence of metastable anatase phase in the titania layers at lower temperatures was attributed to the presence of high stresses within the oxide layers owing to their nanoscale thickness.
关键词： X-ray Photoelectron Spectroscopy,Thin film,Valence band,Surface phase composition,Titania,Titanium
更新于2025-11-21 11:24:58
-
Structural, optical and photoluminescence studies of sol-gel synthesized pure and iron doped TiO2 photocatalysts
摘要： Pure and Iron doped TiO2 nanoparticles were synthesized using the sol-gel method. These materials were characterized by X-ray diffractometer (XRD), high-resolution transmission electron microscope (HR-TEM), scanning electron microscope (SEM), Energy dispersive X-ray (EDX), UV-Vis diffuse reflectance spectroscopy (DRS), Fourier-transform infrared (FTIR), Raman and fluorescence spectrometer. XRD analysis revealed that all the samples were a single phase with anatase nanocrystallite structures. The crystallite size of titania reduced from 9.64 nm to 7 nm with Fe doping. The HRTEM images of the TiO2 and 3% Fe doped TiO2 have revealed that all the particles have a spherical shape with an average particle size of 10 nm and 8 nm respectively. The characteristic peak at 482 cm-1 of the Ti–O bond stretching vibrations can be evidently observed from FTIR analysis. The Raman blue shift was found in the Fe doped TiO2 samples. Fe-doped TiO2 nanoparticles showed a significant red-shift in band edge as compared with pure TiO2 nanoparticles. The redshift of band gap was detected in Fe doped TiO2 nanoparticles. The photoluminescence (PL) emission intensity of Fe doped TiO2 nanoparticles decreases with an increase in Fe doping concentration. The photocatalytic efficiencies of the Fe-doped TiO2 nanoparticles have shown a strong photocatalytic activity (PCA) response. At constant irradiation time, the Fe-doped titania nanoparticles display more catalytic activity compared to undoped TiO2. The photodegradation efficiencies typically decline with an increase in the concentration of Fe+3 doping for the decolorization of methylene blue (MB) under visible light irradiation.
关键词： band gap,Raman modes,photocatalytic activity,TiO2 nanoparticles,methylene blue,PL emission
更新于2025-11-21 11:18:25
-
Broad-band emission and color tuning of Eu3+-doped LiCa2SrMgV3O12 phosphors for warm white light-emitting diodes
摘要： In this study, series of Eu3+-doped LiCa2SrMgV3O12 (LCSMV) phosphors with broad-band emission and color tunable feature were prepared via solid phase reaction. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) results presented a pure cubic phase product with micron-sized and homogeneous distribution of element. Their spectroscopic properties were investigated systematically by photoluminescence excitation (PLE) and emission (PL) spectra, temperature-dependent PL spectra and luminescence decay curves. The LCSMV phosphors displayed a strong absorption to ultraviolet light and a broad cyan emission. Moreover, in Eu3+-doped LCSMV phosphors, Eu3+ ion characteristic emissions at 589, 610, 651 and 705 nm, attributing to the 5D0→7F1, 7F2, 7F3 and 7F4 transitions, were observed. Along with Eu3+ ion concentrations increasing, the emission colors could be readily tuned from cyan to orange and the decay lifetimes of (VO4)3- became shorter. Meanwhile, electric dipole-dipole interaction was responsible to energy migration from (VO4)3- groups to Eu3+ ions. Further, the quantum efficiency (QE) values were estimated to be 32.5% for LCSMV host and 39.3% for LCSMV: 0.01Eu3+ sample. Finally, a LED lamp was prepared by integrating the blend of the LCSMV: 0.01Eu3+ phosphors and commercial blue-emitting BaMgAl10O17:Eu2+ phosphors with NUV chip (365 nm) and exhibited warm white light (CCT = 3655 K, Ra = 90), which may be applied in lighting and display field.
关键词： Self-activated luminescence,Color tunable,Light-emitting diode,Vanadate phosphor,Color rendering index,Broad-band emission
更新于2025-11-20 15:33:11
-
Band gap engineered zinc oxide nanostructures <i>via</i> a sol–gel synthesis of solvent driven shape-controlled crystal growth
摘要： A reliable sol–gel approach, which combines the formation of ZnO nanocrystals and a solvent driven, low shape-controlled, crystal-growth process to form well-organized ZnO nanostructures at temperature is presented. The sol of ZnO nanocrystals showed shape-controlled crystal growth with respect to the solvent type, resulting in either nanorods, nanoparticles, or nanoslates. The solvothermal process, along with the solvent polarity facilitate the shape-controlled crystal growth process, augmenting the concept of a selective adhesion of solvents onto crystal facets and controlling the final shape of the nanostructures. The XRD traces and XPS spectra support the concept of selective adhesion of solvents onto crystal facets that leads to yield different ZnO morphologies. The shift in optical absorption maxima from 332 nm in initial precursor solution, to 347 nm for ZnO nanocrystals sol, and finally to 375 nm for ZnO nanorods, evidenced the gradual growth and ripening of nanocrystals to dimensional nanostructures. The engineered optical band gaps of ZnO nanostructures are found to be ranged from 3.10 eV to 3.37 eV with respect to the ZnO nanostructures formed in different solvent systems. The theoretical band gaps computed from the experimental XRD spectral traces lie within the range of the optical band gaps obtained from UV-visible spectra of ZnO nanostructures. The spin-casted thin film of ZnO nanorods prepared in DMF exhibits the electrical conductivity of 1.14 × 10?3 S cm?1, which is nearly one order of magnitude higher than the electrical conductivity of ZnO nanoparticles formed in hydroquinone and ZnO sols. The possibility of engineering the band gap and electrical properties of ZnO at nanoscale utilizing an aqueous-based wet chemical synthesis process presented here is simple, versatile, and environmentally friendly, and thus may applicable for making other types of band-gap engineered metal oxide nanostructures with shape-controlled morphologies and optoelectrical properties.
关键词： electrical conductivity,ZnO nanostructures,optical band gap,shape-controlled crystal growth,sol–gel synthesis
更新于2025-11-19 16:56:42