- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Keyhole cutting of carbon fiber reinforced polymer using a long-duration nanosecond pulse laser
摘要： The machining performance of a high-energy nanosecond pulse laser with a near-infrared wavelength is investigated for carbon fiber-reinforced polymer (CFRP) with two different fiber arrangements. This research work demonstrates for the first time that a keyhole mode cutting can be achieved for CFRP materials using a high-energy nanosecond pulse laser of a Long Pulse mode (120 ns). Specifically, it is shown that the short-duration Q-Switch mode (8 ns) results in ineffective material removal for CFRP, despite much higher peak laser power intensity than the Long Pulse mode. In Long Pulse mode, multi-pass straight line and contour cutting experiments are further performed to investigate the effect of laser processing parameters and resultant machined surface integrity. Plasma absorption effects using both pulse modes are discussed. The results show that a 2.2 mm thick cross-ply CFRP panel can be cut through using as few as 6 laser passes, and a high-quality machined surface can be produced with a limited heat-affected zone and minimal fiber pull-out using Argon assist gas. The successful outcomes from this work provide the key to enable efficient CFRP laser machining using high-energy nanosecond pulse lasers, and offer insight into the unique energy absorption mechanisms for CFRP laser machining.
关键词： Laser cutting,Keyhole,Long pulse,Nanosecond pulse laser,Carbon fiber reinforced polymer
更新于2025-11-21 11:08:12
-
Effect of laser texturing on the performance of ultra-hard single-point cutting tools
摘要： This paper investigates the cutting performance and anti-adhesive properties of textured single-point polycrystalline diamond (PCD) cutting tools in machining Aluminium 6082 alloys. The micro/nano textures were first milled using a fibre laser (1064-nm wavelength) at different power intensities, feed speeds and pulse durations, and finally characterised using scanning electron microscopy, white light interferometry and energy dispersive X-ray spectroscopy. The effect of different textures on the cutting performance was investigated in turning tests under dry cutting conditions. The test was stopped at regular lengths of cut to allow analysis of height of adhesion through 3D white light interferometry. The data processing of the cutting forces and the microscopical characterisation of the tested cutting tools enabled the evaluation of the effects of texture design, friction coefficient and adhesive properties. The results indicated that feed force in tools with grooves perpendicular to the chip flow direction (CFD) was more stable (20–40 N) than the benchmark (6–41 N). Similarly, the thrust force for tools with grooves parallel to CFD and grooves perpendicular to CFD showed a homogeneous trend fluctuating between 60 and 75 N as compared with the benchmark (ranging between 73 and 90 N). For texture depth in the order of 260 nm and post process roughness in the order of tens of nanometers, a reduction of average friction coefficient (0.28 ± 0.14) was reported when using lasered inserts with grooves parallel to the chip flow direction compared with the benchmark tools (0.34 ± 0.26) corroborated by reduced stiction of workpiece material on the rake face. In machining via textured tools with grooves perpendicular to CFD, the cutting forces were reduced by 23%, and the surface quality of the machined workpiece was improved by 11.8%, making this geometry the preferred choice for finishing applications. Using grooves parallel to CFD reduced the cutting forces by 11.76%, adhesion by 59.36% and friction coefficient by 14.28%; however, it increased the surface roughness of the machined workpiece, making this geometry suitable for roughing operations. For the first time, laser manufacturing is proposed as a flexible technique to functionalise the geometrical and wear properties of PCD cutting tools to the specific applications (i.e. roughing, finishing) as opposed to the standard industrial approach to use microstructurally different PCDs (i.e. grain size and binder %) based on the type of operation.
关键词： Adhesion,Dry cutting,Nanosecond pulse,Laser milling,Polycrystalline diamond insert,Laser surface texturing,Cutting forces
更新于2025-09-16 10:30:52
-
Correlation between defect absorption and nano-second laser-induced damage of HfO2/SiO2 based high reflective coatings at 1064?nm
摘要： The distribution of defect weak absorption and nanosecond pulse laser induced damage characteristics of HfO2/SiO2 multilayers were investigated. A combination of in-situ measurements of defect weak absorption distribution and laser induced damage threshold (LIDT) map was proposed, whereby the evolution of defect weak absorption and the laser induced damage morphology under laser irradiation was studied. During the laser irradiation, some nodular and scalded defects can be removed or passivated by the low flux laser, and the absorption of these defect types was reduced accordingly. Besides, catastrophic destruction defects with enhanced absorption after laser irradiation would develop into catastrophic damage. Further, two-dimensional scanning of the sample surface was used to study the relationship between defects weak absorption and the LIDT. The results indicated that the correlation of defects weak absorption intensity distribution and LIDT map depended on defect evaluation properties during the laser irradiation.
关键词： Nanosecond pulse laser,HfO2/SiO2 multilayers,High reflective coatings,Laser-induced damage,Defect absorption
更新于2025-09-11 14:15:04