- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
The effect of cut depth and distribution for abrasives on wafer surface morphology in diamond wire sawing of PV polycrystalline silicon
摘要： Due to the existence of an acid etch resistant thin amorphous silicon layer over the smooth grooves of the diamond wire sawing polycrystalline silicon wafer surface, the anti-re?ection e?ect is usually not ideal using the mature acidic texturization. The amorphous silicon layer will be produced on the machined surface by material ductile removal. Therefore, during the process of cutting photovoltaic polycrystalline silicon wafers, the material removed in the brittle way is expected and the surface topography of the wafers formed with the brittle fracture is better for the texture fabricating. In this paper, a mathematical model considering the in?uences of process parameters and wire saw parameters was developed based on indentation fracture mechanics. The variations of cutting groove pro?le formed by di?erent material removal modes were also included. The e?ect of abrasives distributed on the wire saw on material removal and surface formation of polysilicon was analyzed. The results showed that most of abrasives removed material with ductile removal mode, however, the volume of the material removed by abrasive in ductile mode is less than 10% of the total removal volume. Brittle fracture removal mode was still the major way of material removal in diamond wire sawing. With the same ratio of the feed rate and wire speed, the faster feed rate and wire speed will not only improve the cutting e?ciency, but also is easier to obtain a brittle fracture surface. There is a critical angle θc for the distribution of abrasives on the wire saw surface. Only when the position angle of the abrasive removing material in brittle mode is less than θc, the brittle fracture can be formed on the wafers surface.
关键词： Diamond wire sawing,Depth of cut,Material removal mode,Photovoltaic polycrystalline silicon
更新于2025-09-23 15:23:52
-
Experimental investigation on the machining characteristics of fixed-free abrasive combined wire sawing PV polycrystalline silicon solar cell
摘要： At present, the fixed abrasive wire sawing (FAWS) technology is gradually used in the photovoltaic industry to cut polycrystalline silicon slices. However, there are obvious directional wire marks, parallel grooves, and amorphous silicon layer on the surface of the slices formed by the FAWS, which leads to a high optic reflectivity of the textured surface obtained after the mature acid etching texturization technology. So the slices cannot meet the requirements of the photovoltaic cell. In the paper, a novel fixed-free abrasive combined wire sawing (FFACWS) technology for cutting PV polycrystalline silicon is presented to solve this problem, by adding loose SiC abrasives to cooling lubricant during the fixed abrasive wire sawing. A single-factor and orthogonal experimental study on sawing characteristics was carried out. The effect of size and mass fraction of SiC abrasives in the slurry, workpiece feed speed and wire speed on the surface morphology, roughness, and kerf loss were studied. The results show that within the range of the processing parameters in the paper studied, the obvious wire marks, parallel grooves, and ductile layers on the surface of the slices can be removed by the FFACWS. The surface roughness of the slices along the wire movement direction and the workpiece feed direction increases with the increase of the mass fraction of SiC abrasives in the slurry and workpiece feed speed and it decreases with the increase of wire speed. But the effect of the size of SiC abrasives is related to the matching of the protruding height of the fixed abrasives on the wire surface along the workpiece feed direction. In the wire movement direction, it increases with the size of SiC abrasives. The kerf loss increases with the increase of size and mass fraction of SiC abrasives in the slurry and the wire speed but has little effect with the change of workpiece feed speed.
关键词： Fixed-free abrasive combined wire sawing,Surface morphology,Surface roughness,Kerf loss,Photovoltaic polycrystalline silicon
更新于2025-09-23 15:19:57