- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Suppression of Iodide Ions Migration via Sb2S3 interfacial Modification for stable Inorganic Perovskite Solar Cells
摘要： In mixed halide perovskite, the halide phase segregation is commonly observed due to halide ions migration, which causes severe stability issues in perovskite devices. Here, we directly revealed the iodide-migration process via potentiostatic treatment in CsPbIBr2 perovskite. The absence of iodide ions was reduced significantly via Sb2S3 interfacial modification. We further employed the DFT calculation to optimize the geometry positions at the perovskite interface and radial distribution functions (RDF) to analyze the atom perturbation. The simulation yielded a slight distortion of perovskite lattice at the interface of Sb2S3-CsPbIBr2 and iodide ions fluctuation was reduced due to the decrease of halide vacancies. In addition, the thermally stimulated current was calculated to evaluate the defects density in the modified perovskite device. Due to the Sb2S3 interaction with perovskite, the device became stable against humidity and maintained photoactive over 400 h. The champion efficiency of 9.31% with 26.31% improvement was obtained in modified CsPbIBr2 perovskite solar cells.
关键词： stability,The mixed halide perovskite,Sb2S3,DFT,iodide ions migration
更新于2025-11-14 15:15:56
-
Fabrication and optimization of nanocube mixed halide perovskite films for solar cell application
摘要： In this article, we report the tailoring of nanostructured mixed halide perovskite MAPb(I1-xBrx)3 films with tunable band gap fabricated by anion exchange reaction. In this process, we used PbBr2 and methyl ammonium iodide (MAI) in order to fabricate mixed halide perovskite films. We have observed an uncommon shape transformation from nanocube-hollow tetraoids-nanocubes/plate. The underlying mechanism of shape transformation was discussed based on experimental results. The driving force for such shape transformation is combined effect of anion exchange reaction between I? and Br? at the solid/liquid interface of PbBr2 and MAI, and mechanical driving force exerted by the spin coating process. The shape transformation is highly reproducible, verified by two step process, dipping as well as spinning process. The best performing device using the nanostructured perovskite films in a device architecture FTO/TiO2/MAPb(I1-xBrx)3/Spiri-OMeTAD/Au shows a current density (Jsc,) of 23.58 mA/cm2, open circuit voltage (Voc) of 0.891 V and fill factor (FF) of 0.608, with a power conversion efficiency (η) of 12.79% in forward sweep. In reverse sweep, the device shows the Jsc (mA/cm2), Voc (V), FF, and η (%) are 23.852, 0.891, 0.716 and 15.237, respectively.
关键词： Nanostructured perovskite films,Anion exchange reaction,Shape transformation,Mixed halide perovskite films,Perovskite solar cell
更新于2025-09-19 17:13:59
-
High-performance mixed-cation mixed-halide perovskite solar cells enabled by a facile intermediate engineering technique
摘要： Perovskite solar cells (PSCs) have attracted considerable attention in the photovoltaic field. However, most efficient mixed-cation mixed-halide perovskite in PSCs suffers from phase instability and large flux of trap states by existing methods, which limits the device performance. Herein, a facile intermediate engineering technique of the MAI-PbI2 intermediate layer via FABr solution is employed to get high-quality mixed perovskite films. The results illustrate that the proposed approach can improve the grain size, morphology, crystallization, consequently reducing defect density of the perovskite layer. The devices which treated with FABr exhibit much-enhanced performance in comparison to the pristine and traditional mixed-cation mixed-halide devices. Consequently, a champion PSC with the best power conversion efficiency of 20.08% is obtained. Moreover, the devices based on the developed FABr-treatment technique also shows much-improved stability than the mixed perovskite-based devices fabricated from the traditional method. Therefore, this approach provides a simple technique to produce high-quality mixed perovskite film and subsequently may facilitate the commercialized production of high-performance PSCs in the future.
关键词： High-quality,Mixed-cation mixed-halide perovskite,FABr,Stability,Intermediate engineering
更新于2025-09-16 10:30:52
-
Well-grown low-defect MAPbI3–xClx films for perovskite solar cells with over 20% efficiency fabricated under controlled ambient humidity conditions
摘要： The conventional MAI [(CH3NH3I (MAI)):PbI2:PbCl2= 3 : 0 : 1 [abbreviated as (3:0:1)]] precursor solution is known to result in CH3NH3PbI3–xClx films with large grain sizes when processed in an inert atmosphere, but it gives non-uniform perovskite films containing lots of voids and cracks when processed in ambient air. Furthermore, a dramatically longer annealing time (usually 100 min) is required for these films (3:0:1) due to the slow formation of the MAPbI3 phase via MACl loss, which is not conducive to perovskite film formation under ambient conditions due to perovskite degradation upon long exposure to moisture. Pure MAPbI3 films can be formed very rapidly from (1:1:0) (MAI:PbI2:PbCl2= 1 : 1 : 0) solution within a short annealing time, but they show small grain sizes and poor film quality. This work demonstrated that a fractional substitution of PbI2 with PbCl2 in the ([MAI]:[PbI2]= 1 : 1) precursor solution has a significant influence on film morphology and quality in terms of crystallization rate, grain size, crystallinity, and trap density of the formed perovskite film. Perovskite films can be formed with 5-min annealing at 100 °C from the precursor (MAI: PbI2:PbCl2= 1: 0.8 : 0.2) processed in ambient air (humidity, 20% RH), exhibiting more uniform, increased grain size and higher film quality with reduced trap densities compared to film (1:1:0), thus leading to significantly improved power conversion efficiency (PCE), from 16.7% for perovskite solar cells (PrSCs) based on film (1:1:0) to 20.04% for the cell based on film (1:0.8:0.2). Further, the effects of R (R= [MAI]/[PbI2+PbCl2]) on morphology, hole mobility, carrier lifetime and efficiency of PrSCs were systematically and thoroughly investigated. This study found that MAPbI3–xClx at R=1 can enable the highest hole mobility and longest carrier lifetime, thus giving the best performance at R=1.
关键词： mixed halide perovskite solar cells,lead chloride,grain size,trap density,crystal growth intermediates
更新于2025-09-12 10:27:22
-
MAPbI3 nanowires prepared by a facile Vapor Transfer Method for simple photodetector
摘要： MAPbI3 nanowires have become one of the promising materials for optoelectronic devices. Herein, a simple template-free vapor transfer approach to synthesize MAPbI3 nanowires on various substrates for optoelectronic device developed. High crystalline MAPbI3 nanowires were realized via methyl-ammonium iodide (MAI) vapor transfer treatment with PbI2 nanowires. PbI2 nanowires were prepared by a self-assembled procedure where PbI2 film was recrystallized and converted to nanowires structure with the exposure of dimethylacetamide (DMAC) vapor. On top of that, the density of MAPbI3 nanowires could be modulated by simply tuning the thickness of PbI2 film. The as-fabricated MAPbI3 nanowires photodetector exhibits a satisfying responsivity of 0.115 A W-1 @3V while the rise time is less than 0.63 s and the decay time is less than 0.73 s. The study presents a bright future of MAPbI3 nanowires for optoelectronic application.
关键词： vapor transfer method,organic mixed halide perovskite,nanowires,nanocrystalline materials,photodetector,sensors
更新于2025-09-11 14:15:04