- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Microstructure and properties of high strength and high conductivity Cu-Cr alloy components fabricated by high power selective laser melting
摘要： Although different kinds of metal materials have been built in the past years, it is difficult to fabricate the components of copper alloys with high strength and high conductivity due to their high reflectivity and thermal conductivity. In this paper, Cu-Cr alloy with high strength and high conductivity was successfully manufactured by high laser power selective laser melting. The microstructure, mechanical properties and conductivity were studied and compared before and after the heat treatment. The microstructure of the as-built sample was columnar grains with very fine cellular sub-structures and precipitates of Cr and Cr2O3. After heat treatment, the Cr particles precipitated from Cu matrix, resulting in simultaneous increase in strength and conductivity. The ultimate tensile strength of 468 MPa, yield strength of 377.33 MPa, and electrical conductivity of 98.31% IACS were achieved, which is even better than the samples fabricated by rolling with post heat treatment.
关键词： Cu-Cr alloy,Electronic conductivity,Laser processing,Microstructure,Mechanical properties
更新于2025-11-28 14:24:20
-
Electrical Properties of Fluoro-Substituted Perovskites Ba2 ? 0.5xCaNbO5.5 ?xFx
摘要： The effect of F--doping on the transport properties of perovskite-type complex oxides based on barium—calcium niobate Ba2CaNbO5.5 is analyzed. It is found that, regardless of the mechanism of introducing fluoride ions into the oxygen sublattice, the О2– and Н+ conductivities increase in the range of low fluoride concentrations due to an increase in the mobility of current carriers.
关键词： perovskite,anion doping,heterovalent doping,protonic conductivity,ionic conductivity
更新于2025-11-21 11:20:42
-
Investigation of temperature and frequency dependence of electrical conductivity and dielectric behavior in CuS and rGO capped CuS nanocomposites
摘要： In this work, we develop a simple and low-cost strategy toward the one-pot synthesis of reduced graphene oxide (rGO) capped copper sulfide (CuS) nanocomposite through an obvious redox transformation reaction between Cu and graphene oxide (GO) without any additive. The prepared CuS and rGO capped CuS nanocomposite have been characterized by various physicochemical techniques for the observation of shape, morphology, and structure. It reveals the average size of the synthesized samples in the range of 10–30 nm with the hexagonal structure. The UV–vis absorption spectra exposed the strong absorption peak of CuS and rGO capped CuS composites in the range of NIR region was observed. The synthesized samples displayed high dielectric constant and electrical conductivity in a wide range of frequency (102–106 Hz). The effect of temperature on the electrical conductivity of the synthesized rGO capped CuS nanocomposite was also investigated. The excellent electrical conductivity performance is ascribed to the synergistic effect between CuS and rGO. As the temperature increases, the maximum electrical conductivity of rGO capped CuS composite was exponentially increased at high temperature. The synthesized composite with a high dielectric constant and electrical conductivity is a promising material in high capacitance, and further, it is used as electrode materials for supercapacitors and energy storage applications.
关键词： electrical conductivity,temperature effect,CuS nanocomposites,reduced graphene oxide,dielectric constant
更新于2025-11-21 11:18:25
-
Origin of anisotropy and compositional dependence of phonon and electron transport in ZnO based natural superlattices and role of atomic layer interfaces
摘要： Reaction of ZnO with trivalent ions can form natural superlattice (SL) compounds, which possess unusual structural characteristics and strong anisotropic physical transport properties. In this work, by synthesizing strongly textured bulk polycrystals of pure SL phases and performing characterization and measurements for both in-plane and cross-sectional directions, we revealed the strongly crystal orientation dependent transport properties. The observed compositional or SL interface spacing dependent electrical conductivity is largely attributed to the overall doping of ZnO wurtzite regions. The atomic layer SL interfaces are phonon barriers, and the interfacial thermal (Kapitza) resistance depends on SL interface spacing. The transport direction perpendicular to these SL interfaces are electron-conductive paths with remarkably higher electron mobility. There are electron potential barriers associated with these atomic layer SL interfaces. The effective and absolute potential barrier heights are determined, which are proportional to the natural conduction band discontinuities. The current study provides new findings and knowledge about the role of SL interfaces in phonon and electron transport process in these ZnO based natural SLs. The present work can be useful and inspiring to design and modify complex layer-structured compounds, including synthetic superlattice systems, for a variety of applications where energy carriers transport is involved.
关键词： Interfaces,Superlattices,Electron potential barrier,Interfacial thermal (Kapitza) resistance,Thermal conductivity,ZnO
更新于2025-11-21 11:03:13
-
P‐type Sb‐doped Cu <sub/>2</sub> O Hole Injection Layer Integrated on Transparent ITO Electrode for Acidic PEDOT:PSS‐Free Quantum Dot Light Emitting Diodes
摘要： It is developed that transparent p-type Sb-doped cuprous oxide (ACO) integrated Sn-doped In2O3 (ITO) film as hole injection layer (HIL) and anode combined electrodes for quantum dot light emitting diodes (QD-LEDs) to substitute acidic PEDOT:PSS HIL based electrode. By graded co-sputtering of ACO and ITO targets, the graded p-type ACO buffer layer can be integrated on the surface region of the ITO electrodes. P-type conductivity of the ACO film for acting as effective HIL in QD-LEDs is confirmed by a positive Hall coefficient (1.74 (cid:1) 10 (cid:3)1). Due to the well-matched work function of p-type ACO on the ITO electrodes, the acidic PEDOT:PSS-free QD-LEDs exhibited typical current-voltage-luminescence of QD-LEDs. The successful operation of PEDOT:PSS-free QD-LED with p-type ACO integrated ITO electrode indicates that ACO and ITO anode graded sputtering is simpler fabrication steps for cost-effective QD-LEDs and elimination of interfacial reactions caused by the acidic PEDOT:PSS layer for reliable QD-LEDs.
关键词： Sn-doped In2O3,acidic PEDOT:PSS,hole injection layer,p-type conductivity,Sb-doped Cu2O,quantum dots light emitting diodes
更新于2025-11-21 10:59:37
-
Band gap engineered zinc oxide nanostructures <i>via</i> a sol–gel synthesis of solvent driven shape-controlled crystal growth
摘要： A reliable sol–gel approach, which combines the formation of ZnO nanocrystals and a solvent driven, low shape-controlled, crystal-growth process to form well-organized ZnO nanostructures at temperature is presented. The sol of ZnO nanocrystals showed shape-controlled crystal growth with respect to the solvent type, resulting in either nanorods, nanoparticles, or nanoslates. The solvothermal process, along with the solvent polarity facilitate the shape-controlled crystal growth process, augmenting the concept of a selective adhesion of solvents onto crystal facets and controlling the final shape of the nanostructures. The XRD traces and XPS spectra support the concept of selective adhesion of solvents onto crystal facets that leads to yield different ZnO morphologies. The shift in optical absorption maxima from 332 nm in initial precursor solution, to 347 nm for ZnO nanocrystals sol, and finally to 375 nm for ZnO nanorods, evidenced the gradual growth and ripening of nanocrystals to dimensional nanostructures. The engineered optical band gaps of ZnO nanostructures are found to be ranged from 3.10 eV to 3.37 eV with respect to the ZnO nanostructures formed in different solvent systems. The theoretical band gaps computed from the experimental XRD spectral traces lie within the range of the optical band gaps obtained from UV-visible spectra of ZnO nanostructures. The spin-casted thin film of ZnO nanorods prepared in DMF exhibits the electrical conductivity of 1.14 × 10?3 S cm?1, which is nearly one order of magnitude higher than the electrical conductivity of ZnO nanoparticles formed in hydroquinone and ZnO sols. The possibility of engineering the band gap and electrical properties of ZnO at nanoscale utilizing an aqueous-based wet chemical synthesis process presented here is simple, versatile, and environmentally friendly, and thus may applicable for making other types of band-gap engineered metal oxide nanostructures with shape-controlled morphologies and optoelectrical properties.
关键词： electrical conductivity,ZnO nanostructures,optical band gap,shape-controlled crystal growth,sol–gel synthesis
更新于2025-11-19 16:56:42
-
Electrical conductivity and conduction mechanisms in (Na <sub/>0.5</sub> Bi <sub/>0.5</sub> TiO <sub/>3</sub> ) <sub/>1?x</sub> (BiScO <sub/>3</sub> ) <sub/>x</sub> (0.00 ≤ <i>x</i> ≤ 0.25) solid solutions
摘要： The electrical properties of (Na0.5Bi0.5TiO3)1-x(BiScO3)x (NBT-BS, 0.00 ≤ x ≤ 0.25) solid solutions are established by ac impedance spectroscopy and electromotive force transport number measurements. The bulk conductivity decreases with increasing BS incorporation but the oxide-ion transport number remains high (≥0.85) over a wide compositional range 0.00 ≤ x ≤ 0.15 and drops to ≈0.7 for x ≥ 0.20. NBT-BS solid solutions can only present either predominant oxide-ion conduction or mixed ionic-electronic conduction behaviour, indicating that oxide-ion conduction cannot be fully eliminated by incorporation of BS. This is in contrast from our previous study where incorporation of ≈7% BiAlO3 (BA) can fully suppress the oxide-ion conduction in NBT. The conductivity–composition relationships of NBT-BS solid solutions are attributed to a competing effect from lattice expansion, which enlarges the channel for oxygen ion migration, with trapping between B-site acceptor ions, Sc'Ti, and oxygen vacancies, V??O, which decreases oxygen ion migration. Comparisons between NBT-BS, NBT-BA and NBT-BiGaO3 (BG) solid solutions suggest that small acceptor ions on the B-site are more effective in trapping oxygen vacancies and consequently more effective to suppress the oxide-ion conduction and thus reduce dielectric loss at elevated temperatures.
关键词： transport number,electrical conductivity,solid solutions,sodium bismuth titanate,oxide-ion conduction,conduction mechanisms,impedance spectroscopy,BiScO3
更新于2025-11-14 17:28:48
-
Investigations on structural, optical and electrical property of ZnO-CuO core–shell nano-composite
摘要： ZnO-CuO core–shell nano-composite was synthesized by two-stage assisted wet-chemical sol-gel method. The nano-composite investigated by X-ray diffraction, ?eld effective scanning electron microscope, UV–visible spectroscopy and Electrical property at different frequency range 100 Hz to 2 MHz and at different temperature. The X-ray diffraction pattern shows poly-crystalline growth of sample, UV–visible spectrum shows higher absorption in ZnO-CuO nano-composite as compare ZnO, which can be understood in vicinity of morphology and heterojunction. The electrical conductivity of nano-composite has been increased with frequency and temperature due to defect available in the sample and thermal excitation of the charges in the sample respectively.
关键词： Nano-composite,Sol–gel,Core–shell,AC conductivity
更新于2025-11-14 17:28:48
-
Dielectric and Piezoelectric Properties of Textured Lead-Free Na0.5Bi0.5TiO3-Based Ceramics
摘要： This work provides a comparative study of the dielectric and piezoelectric properties of randomly oriented and textured 0.88Na0.5Bi0.5TiO3-0.08K0.5Bi0.5TiO3-0.04BaTiO3 (88NBT) ceramics. Textured ceramics were fabricated by template grain growth (TGG) method using NaNbO3 (NN) for templates. For textured ceramics with 4 wt% NN templates, a Lotgering factor of 96% and piezoelectric coe?cient d33 of 185 pC/N were obtained. Compared to the randomly oriented ceramics, textured ceramics show lower strain hysteresis (H = 7.6%), higher unipolar strain of 0.041% with corresponding large signal piezoelectric coe?cient d33* of 200 pm/V at applied ?eld of 2 kV/mm. This enhancement can be explained by the grain orientation along <001> direction by texturing, where an engineered domain con?guration is formed after polarization, leading to decreased hysteresis and increased piezoelectric property.
关键词： electrical conductivity,textured ceramics,template grain growth,piezoelectric materials
更新于2025-11-14 17:28:48
-
Structural characterization and electrical conductivity analysis of MoO3–SeO2–ZnO semiconducting glass nanocomposites
摘要： A series of glass nanocomposite samples of the general composition formula xMoO3–(1-x) (0.5SeO2–0.5ZnO) for x = 0.05, 0.1, 0.2, and 0.3 have been prepared by solid-state reaction, i.e., slow cooling process. The structural characteristics have been explored by analyzing X-ray di?raction patterns, Fourier-transform infrared, and UV–Vis spectra. The superposition of di?erent nanophases SeO2, SeO3, ZnO, MoO3, Zn (SeO3), Zn (SeO4), Zn (MoO4), Zn2Mo3O8 and ZnMo8O10 over the amorphous glassy matrices have been identi?ed, and their crystallite sizes have been evaluated as well. Fourier transform infrared (FTIR) spectra reveal di?erent types of bonding like Zn–O–Se type and stretching vibrations of MoO6 octahedral units. It is observed that with increasing MoO3 concentration, the estimated values of optical bandgap energy, Urbach energy, and average crystallite size reduce. The dependency of electrical conductivity on frequency and temperature have been analyzed using Almond-West formalism and Jonscher's universal power-law. The non-linear character of DC conductivity and di?erent activation energies at low and high-temperature regions a?rm that the present glassy systems exhibit semiconducting nature. Moreover, DC conduction process is due to small polaron hopping through localized or defect states. The decreasing trend of power-law exponent (s) with temperature rise reveals that AC conduction mechanism is consistent with the correlated barrier-hopping (CBH) model. The existing correlated barrier-hopping model has been modi?ed to attain reasonable values of ?tting parameters and to obtain theoretical values of ideal thermodynamic glass transition temperature. The AC conductivity activation energy and free energy required for small polaron migration reduce with increasing conductivity. The scaling property emphasizes that conductivity relaxation process is subjected to the structure of the composition and does not depend on temperature.
关键词： XRD,UV–vis spectroscopy,Glass nanocomposites,Correlated barrier hopping model,DC and AC conductivity,FTIR
更新于2025-11-14 17:28:48