- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
On-line Writing of Fiber Bragg Grating Array on a Two-mode Optical Fiber for Sensing Applications
摘要： On-line fabricated fiber Bragg grating (FBG) array and its sensing potentials have attracted plenty of attention in recent years. In this paper, FBG arrays are written on-line on a two-mode fiber, and this two-mode fiber Bragg grating (TM-FBG) is further experimentally investigated for temperature and curvature sensing. The responses of this sensor were characterized by 11.2 pm/°C for temperature and ?0.21 dB/m?1 for curvature, respectively. Based on the measurements, a dual-parameter fiber sensing system was developed, which can realize the quasi-distributed, simultaneous detection of temperature and curvature, making it suitable for structural health monitoring or perimeter security.
关键词： on-line grating writing,fiber Bragg grating,two-mode fiber,curvature sensing,temperature sensing
更新于2025-11-28 14:23:57
-
Role of Yb3+ ion on the evaluation of energy transfer and cross-relaxation processes in Gd2Ce2O7: Yb3+, Er3+ phosphors
摘要： Energy transfer (ET) and cross-relaxation (CR) processes play significant roles in regulating emitting colors and intensity of upconversion (UC) materials. Calculating the coefficients in ET and CR processes can provide visual descriptions for evaluating the UC luminescence properties. Here, we find that those ET and CR processes are responsible for the color-tunable properties in Gd2Ce2O7: Yb3+, Er3+ phosphors. By solving the rate equation, mathematical expressions are established to calculate the ET and CR coefficients based on the experimental UC spectra and lifetimes. The results are benefit to evaluate the efficiencies of ET and CR processes in quantization in different Yb3+ ion concentrations doped samples. The coefficients of ET process arise from 1.05 to 7.93 × 1017 cm3s?1 while those of CR process increase from 2.69 to 72.01 × 1017 cm3s?1 with increasing the Yb3+ ion concentration, which suggest that the CR and ET processes are efficient in Gd2Ce2O7 host. Furthermore, potential temperature sensing properties are also evaluated according to the fluorescence intensity ratio of 2H11/2 and 4S3/2 levels and the maximal sensitivity (S) is achieved about 0.00337 K?1 at 503 K. This work provides an insight into the evaluation of those UC processes and reveals the capacity in color-tunable and temperature sensing aspects.
关键词： Upconversion,Mathematical expression,Cross-relaxation,Temperature sensing,Energy transfer
更新于2025-11-14 17:03:37
-
Improved negative thermal quenching effect via high sensitizer doping content in NaGdF4 based active-core/active-shell architecture
摘要： The strategies of introducing interior defects and reducing mean particle size have been applied to improve negative thermal quenching effect (TQE) in Yb3+ sensitized fluoride upconversion (UC) nanocrystals (NCs) recently. Herein, an active-core/active-shell structure with high total Yb3+ doping content is used to enhance the absorption intensity of Er3+ ions. Moreover, the Er3+ activators are doped into the shell to enable the energy migration process from activators to surface defects. In this scenario, with the rise of temperature, the suppression degree of this energy migration process is enlarged followed by an improved negative TQE. Specifically, with rising the temperature from 293 K to 413 K, the integral upconversion emission intensity of 40Yb: NaGdF4@60Yb/2Er: NaGdF4 NCs increases by ~ 8.24 times, while that of NaGdF4@20Yb/2Er: NaGdF4 NCs with a similar mean particle size only enhances ~ 3.44 times.
关键词： Yb3+ concentration,upconversion,temperature sensing,negative thermal quenching
更新于2025-11-14 17:03:37
-
[ASME ASME 2018 International Technical Conference and Exhibition on Packaging and Integration of Electronic and Photonic Microsystems - San Francisco, California, USA (Monday 27 August 2018)] ASME 2018 International Technical Conference and Exhibition on Packaging and Integration of Electronic and Photonic Microsystems - Next Gen Test-Vehicle to Simulate Thermal Load for IoT FPGA Applications
摘要： As semiconductor device feature size scales and circuit performance increases, power dissipation and thermal management are becoming very important. Attention to thermal considerations is required throughout the chip development cycle from preliminary architecture planning to deployment on customer board and beyond. This paper describes a versatile thermal test vehicle that can be used to address these requirements. We discuss the architecture and implementation of a specially designed test-vehicle chip, followed by its operation. The programmability and flexibility of this vehicle will be highlighted. In addition, we cover other usage of this vehicle which includes modelling of chip-level thermal behavior with different floorplan, simulating thermal loads in IoT FPGA applications, cross-calibrating thermal numerical simulators with measured silicon data and evaluating the thermal impact of different package form-factor / material (such as thermal interface material) and cooling solutions. The abovementioned chip was fabricated using 0.18um technology and assembled in a flip-chip package. The reminder of this evaluation system is a simple, inexpensive tester from which a software is run to program the chip and to measure the spatial & temporal temperature values. Measured thermal data from different use cases are presented in this paper.
关键词： on-chip temperature measurement,thermal management,package development,package-level thermal evaluation,on-die heating,IoT servers,on-die temperature sensing,characterization methodology,thermal evaluation tool
更新于2025-09-23 15:23:52
-
The upconversion photoluminescence and temperature sensing abilities of Pb(Zn1/3Nb2/3)O3-9PbTiO3 crystals induced by Er3+/Yb3+ doping
摘要： Er3+/Yb3+-doped Pb(Zn1/3Nb2/3)O3-9PbTiO3 ferroelectric crystals were grown by the high-temperature solution method. The micromorphology, phase structure, and upconversion photoluminescence of obtained crystals were analyzed and investigated. As the results suggest, the crystals displayed typical lamellar growth and possessed a pure perovskite structure. Excited by a 980 nm laser, the characteristic upconversion (UC) emissions of Er3+ were observed at room temperature. The luminescence intensity improved with the increasing of excitation power and reached its maximum at 1056 mW. Two-photon process was demonstrated at lower power range. As the temperature increased from 213 to 493 K, the luminescence intensity weakened continuously. An apparent difference in variation trend between two thermally coupled levels (2H11/2 and 4S3/2) was also observed, which was ascribed to the redistribution of electrons at two levels at the heating process. Based on this dependence, the temperature sensing abilities were examined with the help of the fluorescence intensity ratio (FIR) technique. The absolute sensitivity SA increased in the measurement temperature range and its maximum of 0.0033 K-1 was obtained at 493 K. Moreover, low conversion from incident light into heat was also demonstrated, which indicates the feasibility for crystal luminescence at high power pumping. These results make Er3+/Yb3+-doped Pb(Zn1/3Nb2/3)O3-9PbTiO3 crystals become a promising candidate in optical devices and temperature sensors.
关键词： Two-photon process,Temperature sensing,FIR technique,Ferroelectric crystals,UC emissions
更新于2025-09-23 15:23:52
-
Highly efficient green upconversion luminescence of ZnMoO4:Yb3+/Er3+/Li+ for accurate temperature sensing
摘要： Upconversion luminescence and optical temperature sensing properties of Yb3+/Er3+/Li+ tri-doped ZnMoO4 phosphors were investigated. It has been demonstrated that Li+ doping affected not only the local symmetry of Yb3+ and Er3+ but also the distribution of them in the host lattice. As a result, the significantly improved green upconversion luminescence was obtained when excited at 980 nm. The pumping power dependent photo-thermal behavior was used to evaluate the reliability of upconversion temperature sensing. An accurate temperature scale was established by eliminating the impact of thermal effect, and the sensing ability was evaluated via a comparison with the results reported in literatures.
关键词： Li+ doping,Upconversion luminescence,Thermal effect,Temperature sensing,ZnMoO4
更新于2025-09-23 15:23:52
-
Multichannel luminescence properties and ultrahigh-sensitive optical temperature sensing of mixed-valent Eu2+/Eu3+ co-activated Ca8ZrMg(PO4)6(SiO4) phosphors
摘要： A novel dual-emitting Ca8ZrMg(PO4)6(SiO4): (Eu3+, Eu2+) phosphors with ultrahigh-sensitive optical temperature sensing are prepared by a conventional solid-state method. The Eu2+/Eu3+ co-activated Ca8ZrMg(PO4)6(SiO4) phosphors exhibit efficient dual-mode emissions with an intense, broad blue emission peaked at 414 nm and a relative bright red-emitting centered at 614 nm under 297 nm UV-light excitation, respectively. Furthermore, the fluorescence intensity ratio (FIR) technology is applied to analyze the optical temperature sensing performance of Ca8ZrMg(PO4)6(SiO4): (Eu3+, Eu2+) phosphors. Based on different thermal quenching behavior of Eu2+ and Eu3+ dual-emitting centers, linear temperature-dependent FIR between Eu2+ and Eu3+ is obtained. The maximal absolute sensitivity reaches as high as 5.94% K-1, which is superior to that for the other luminescent temperature sensing materials reported previously. Analyses of the temperature-dependent photoluminescence spectra and configurational coordinate diagrams for Ca8ZrMg(PO4)6(SiO4): (Eu3+, Eu2+) phosphors indicate that the temperature-sensitive variation in FIR of Eu2+ to Eu3+ is originated from the difference in thermal quenching activation energy for 5d→4f transition of Eu2+ and 5D0→7FJ (J=1, 2, 4) transitions of Eu3+. These results reveal that the Ca8ZrMg(PO4)6(SiO4): (Eu3+, Eu2+) phosphors show glorious potential in high temperature optical thermometry.
关键词： Co-activated,Ca8ZrMg(PO4)6(SiO4),Optical temperature sensing,FIR
更新于2025-09-23 15:23:52
-
Soil Temperature Variability in Complex Terrain Measured Using Fiber-Optic Distributed Temperature Sensing
摘要： Soil temperature (Ts) exerts critical controls on hydrologic and biogeochemical processes, but the magnitude and nature of Ts variability in a landscape setting are rarely documented. Fiber-optic distributed temperature sensing (DTS) systems potentially measure Ts at high density across a large extent. A fiber-optic cable 771 m long was installed at a depth of 10 cm in contrasting landscape units (LUs) defined by vegetative cover at Upper Sheep Creek in the Reynolds Creek Experimental Watershed (RCEW) and Critical Zone Observatory in Idaho. The purpose was to evaluate the applicability of DTS in remote settings and to characterize Ts variability in complex terrain. Measurement accuracy was similar to other field instruments (±0.4°C), and Ts changes of approximately 0.05°C at a monitoring spatial scale of 1 m were resolved with occasional calibration and an ambient temperature range of 50°C. Differences in solar inputs among LUs were strongly modified by surface conditions. During spatially continuous snow cover, Ts was practically homogeneous across LUs. In the absence of snow cover, daily average Ts was highly variable among LUs due to variations in vegetative cover, with a standard deviation (SD) greater than 5°C, and relatively uniform (SD < 1.5°C) within LUs. Mean annual soil temperature differences among LUs of 5.2°C was greater than those of 4.4°C associated with a 910-m elevation difference within the RCEW. In this environment, effective Ts simulation requires representation of relatively small-scale (<20 m) LUs due to the deterministic spatial variability of Ts.
关键词： landscape units,complex terrain,vegetative cover,fiber-optic cable,snow cover,spatial variability,Soil temperature,distributed temperature sensing
更新于2025-09-23 15:22:29
-
High concentration Eu3+-doped NaYb(MoO4)2 multifunctional material: Thermometer and plant growth lamp matching phytochrome PR
摘要： Phytochromes PR and PFR are distributed in various organs of plant, phytochrome PR absorbs red light and phytochrome PFR absorbs far-red light, respectively, so the flower induction, etc. can be controlled by changing the ratio of red light to far-red light. The emission of Eu3+ (transition from 5D0/7F2) is located at the red range and matches with the absorption band of PR. Herein, we synthesized successfully NaYb(MoO4)2: Eu3+ phosphors with the high doping concentration (50%) by hydrothermal method with further calcinations. The LED device was also fabricated by the blue InGaN chip combined with the red phosphors NaYb(MoO4)2: 50%Eu3+ based on the excellent luminescent intensity. Moreover, the effect of temperature on the excitation intensity ratio of MoO4 2- to Eu3+ has also been studied, which provided the possibility of simultaneous luminescence and temperature measurement. This work is the first time to use Eu3+ as a red source matching PR, and the red phosphors have potential value to control plant growth.
关键词： Down-conversion luminescence,Temperature sensing,LEDs,Plant cultivation,Red phosphors
更新于2025-09-23 15:22:29
-
Sm3+, Tb3+ co-doped NaLa(MoO4)2 temperature sensing materials based on the fluorescence intensity ratio
摘要： In optical temperature sensors, the method of measuring temperature based on Fluorescence Intensity Ratio (FIR) has been paid tremendous attention due to its fortissimo anti-excitation power noise and the ability of anti-signal transmission channel to transmit light unsteady [1e10]. The above method has the advantages of non-contact, resistance to high temperature, wide temperature range, quick response and being able to measure small objects. The optical temperature sensing technology based on the FIR is used to detect the temperature through detecting the ratio of emitted fluorescence intensity between a pair of specific thermal coupling energy levels related to the temperature [11e15]. The fluorescence emission efficiency of Sm3+ doped oxide in 4G5/2 energy level was quite high. Sm3+ emits bright orange-red color. Tb3+ doped oxide is the strongest fluorescence branch in emission from 5D4- 7F5 [16,17]. If the thermal-quenching trend of luminescence of Sm3+ and Tb3+ is different, the FIR will change with temperature. So FIR can be used to indicate the temperature. Therefore, intensive study of Sm3+ and Tb3+ co-doped materials has great prospects, because it can reveal broad luminescence color variability from green to red. Molybdate has chemical stability and thermal stability, rare earth ions have strong 4f-4f transition absorption and transition emission in this host. Therefore it is a wally host [18,19]. Based on the above-mentioned reasons, in this paper Sm3+, Tb3+ co-doped NaLa(MoO4)2 samples of different morphology have been prepared and studies the temperature sensing characteristics.
关键词： Phosphor,Optical temperature sensing,Chemical synthesis,Luminescence
更新于2025-09-23 15:22:29