- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Stable Sn/Pb-Based Perovskite Solar Cells with a Coherent 2D/3D Interface
摘要： Low-band-gap metal halide perovskite semiconductor based on mixed Sn/Pb is a key component to realize high-ef?ciency tandem perovskite solar cells. However, the mixed perovskites are unstable in air due to the oxidation of Sn2+. To overcome the stability problem, we introduced N-(3-aminopropyl)-2-pyrrolidinone into the CH3NH3Sn0.5Pb0.5IxCl3-x thin ?lm. The carbonyl group on the molecule interacts with Sn2+/Pb2+ by Lewis acid coordination, forming vertically oriented 2D layered perovskite. The 2D phase is seamlessly connected to the bulk perovskite crystal, with a lattice coherently extending across the two phases. Based on this 2D/3D hybrid structure, we assembled low-band-gap Sn-based perovskite solar cells with power conversion ef?ciency greater than 12%. The best device was among the most stable Sn-based organic-inorganic hybrid perovskite solar cells to date, keeping 90% of its initial performance at ambient condition without encapsulation, and more than 70% under continuous illumination in an N2-?lled glovebox for over 1 month.
关键词： power conversion efficiency,2D/3D interface,stability,Sn/Pb-based,perovskite solar cells
更新于2025-11-21 11:18:25
-
Surface Passivation of Perovskite Solar Cells Toward Improved Efficiency and Stability
摘要： The advancement of perovskite solar cells (PVSCs) technology toward commercialized promotion needs high efficiency and optimum stability. By introducing a small molecular material such as tetratetracontane (TTC, CH3(CH2)42CH3) at the fullerene (C60)/perovskite interface of planar p-i-n PVSCs, we significantly reduced the interfacial traps, thereby suppressing electron recombination and facilitating electron extraction. Consequently, an improved efficiency of 20.05% was achieved with a high fill factor of 79.4%, which is one of the best performances for small molecular-modified PVSCs. Moreover, the hydrophobic TTC successfully protects the perovskite film from water damage. As a result, we realized a better long-term stability that maintains 87% of the initial efficiency after continuous exposure for 200 h in air.
关键词： Surface defect,Charge transport,Surface passivation,Perovskite solar cells
更新于2025-11-21 11:01:37
-
Ultra-flexible perovskite solar cells with crumpling durability: toward a wearable power source
摘要： Perovskite materials hold great potential as photovoltaic power sources for portable devices owing to their mechanical flexibility and high performance; however, the flexibility and e?ciency require further improvement to attain practical viability. We investigated the mechanical fracture behavior of polycrystalline perovskite films by varying the substrate thickness and applying the neutral plane concept. This enabled us to fabricate a crack-free perovskite film on an ultra-thin substrate (B2.5 mm) and to demonstrate ultra-flexible solar cells with high e?ciency (17.03%) with unprecedented flexibility sustained after 10 000 cycles of bending at a 0.5 mm radius. This represents a high e?ciency of 13.6% for large-area flexible perovskite solar cells (1.2 cm2), fabricated by using a hybrid transparent electrode composed of a metal mesh grid and conducting polymer. Using a protective layer to achieve the neutral plane concept, our ultra-flexible perovskite solar cells are demonstrated to be durable even after 100 crumpling cycles. Our approach paves the way to fabricate flexible perovskite solar cells for portable power sources.
关键词： wearable power source,Perovskite solar cells,mechanical durability,neutral plane concept,flexible
更新于2025-11-21 10:59:37
-
Understanding the Impact of Cu-In-Ga-S Nanoparticles Compactness on Holes Transfer of Perovskite Solar Cells
摘要： Although a compact holes-transport-layer (HTL) ?lm has always been deemed mandatory for perovskite solar cells (PSCs), the impact their compactness on the device performance has rarely been studied in detail. In this work, based on a device structure of FTO/CIGS/perovskite/PCBM/ZrAcac/Ag, that effect was systematically investigated with respect to device performance along with photo-physics characterization tools. Depending on spin-coating speed, the grain size and coverage ratio of those CIGS ?lms on FTO substrates can be tuned, and this can result in different hole transfer ef?ciencies at the anode interface. At a speed of 4000 r.p.m., the band level offset between the perovskite and CIGS modi?ed FTO was reduced to a minimum of 0.02 eV, leading to the best device performance, with conversion ef?ciency of 15.16% and open-circuit voltage of 1.04 V, along with the suppression of hysteresis. We believe that the balance of grain size and coverage ratio of CIGS interlayers can be tuned to an optimal point in the competition between carrier transport and recombination at the interface based on the proposed mechanism. This paper de?nitely deepens our understanding of the hole transfer mechanism at the interface of PSC devices, and facilitates future design of high-performance devices.
关键词： perovskite solar cells,compactness,Cu-In-Ga-S,hole transfer,holes transport layer,recombination
更新于2025-11-21 10:59:37
-
Transparent Sn-doped In2O3 electrodes with a nanoporous surface for enhancing the performance of perovskite solar cells
摘要： We report on a simple and efficient process to enhance the performance of perovskite solar cells by using ITO electrodes with a nanoporous surface formed by wet-etching of self-agglomerated Ag nanoparticles. Effective removal of the Ag nanoparticles embedded in the surface of the ITO electrodes result in a nanoporous structure without changing the ITO's sheet resistance (10.17 Ω/square) and optical transmittance (89.08%) at a 550 nm wavelength. Examinations with a scanning electron microscope, a transmission electron microscope, and two-dimensional porous mapping show that the nanoporous ITO surface has an increased contact area with the electron transport layer, which enhanced the carrier extraction efficiency of the perovskite solar cells. Compare to perovskite solar cells fabricated on typical ITO with a flat surface morphology, the perovskite solar cells fabricated on the nanoporous-surface ITO show a higher fill factor of 81.1% and a power conversion efficiency of 20.1%. These results indicate that modified ITO surfaces with nano-scale porosity provide a simple and efficient method to improve the power conversion efficiency of perovskite solar cells without a complicated process.
关键词： Contact area,Nanoporous surface,Sn-doped In2O3,Ag agglomeration,Perovskite solar cells
更新于2025-11-21 10:59:37
-
Multifunctional atomic force probes for Mn2+ doped perovskite solar cells
摘要： Doping in organic–inorganic perovskite semiconductors is an effective method to tailor their optoelectronic properties. In this work, manganese-doped perovskite films with different Mn/Pb ratios ranging from 0% to 2% were systematically studied. The device performance of 0.2% Mn-doped devices was improved compared to that of a device without Mn. However, a further increase of the doping concentration induced a decrease in performance. Several characteristics (especially different scanning probe microscopy characteristics) reveal that an increased dopant concentration results in reduced crystallinity and a change in the film morphology and causes a deterioration in photovoltaic performance for higher dopant concentrations. In the best-performing samples (0.2%), a shift in the valence band level and band gap are found which are responsible for the increased open circuit voltage, while increased grain boundaries and lower surface charge density are responsible for a small reduction in the short circuit current. Thus, multifunctional scanning probe microscopy approaches, combined with different film characterization techniques, offer us effective tools to investigate the impact of doping in the perovskite materials and the corresponding device performance.
关键词： EFM,SKPM,C-AFM,Perovskite solar cells
更新于2025-11-20 15:33:11
-
Perovskite solar cells based on polyaniline derivatives as hole transport materials
摘要： Perovskite solar cells (PSC) have been extensively studied over the past few years in both academia and industry. Despite their appeal as a low cost and ease processing PV-technology, PSC still rely on materials that are expensive, turning the large-scale production more challenging. In this work, polyaniline (PAni) and its derivative poly(o-methoxyaniline) are employed as hole transport material (HTM) in PSC, replacing the most explored HTM, spiro-OMeTAD. These very well established conducting polymers are doped with 4-dodecylbenzenesulfonic acid (DBSA) to enhance their conductivity. The correlation between the performance of the solar cells using doped and undoped conducting polymers and different metallic contacts are also evaluated. The best power conversion efficiency was 10.05% using doped PAni-DBSA with Au as contact, which is similar to the performance exhibited by our standard device using Spiro-OMeTAD as HTM.
关键词： hole transport material,perovskite solar cells,polyaniline
更新于2025-11-19 16:56:42
-
New Strategy to Overcome the Instability That Could Speed up the Commercialization of Perovskite Solar Cells
摘要： Current efficiency of perovskite solar cells has reached 23.7%, which is comparable with silicon solar cells. However commercial development is seriously hindered by the instability of the perovskite, especially under moisture conditions. Therefore it is crucial to gain clear understanding of the mechanism of degradation of organic–inorganic perovskite in order to achieve stable perovskite devices. In this paper, the formation and the degradation of perovskite film on different charge transport layers such as a compact TiO2 layer, compact ZnO layer, and ZnO foil, Si nanowires, and porous Si are studied. In addition, density functional theory studies are carried out to better understand the interaction between the perovskite film and substrates. Experimental and theoretical results are combined to draw more reliable conclusion regarding the degradation mechanism. Most notably, the investigations show that the interaction between the iodine (I) atom in the perovskite layer and substrate determine the stability of perovskite cells. As a result, Si has minimum interaction with I atoms and shows maximum stability, while perovskite film degrades on TiO2 film almost immediately.
关键词： degradation,stability,perovskite solar cells,mechanism
更新于2025-11-19 16:56:42
-
A systematic approach to ZnO nanoparticle-assisted electron transport bilayer for high efficiency and stable perovskite solar cells
摘要： Minimizing the interface loss of perovskite solar cells is critical to achieving high photovoltaic performance, and intensive research is underway on interfacial engineering in this regard. In this work, we introduce a ZnO nanoparticles (ZnO NPs) interlayer between phenyl-C61-butyric acid methyl ester (PCBM) and a metal electrode in order to reduce the interface loss due to charge recombination and device degradation, and also investigate the dependence of device performance on the thickness and morphology of the PCBM and PCBM/ZnO electron transport bilayer. After achieving optimized PCBM and ZnO thickness, the PCBM/ZnO bilayer-based devices reached an average power conversion efficiency of 15.63% (Max. 16.39%) with an open circuit voltage of 1.05 V, short circuit current density of 18.69 mA cm-2, and fill factor of 79.95%. In addition, hysteresis behavior and atmospheric stability are significantly improved by the incorporation of a PCBM/ZnO bilayer. Therefore, the implementation of a PCBM/ZnO electron transport bilayer is a promising approach toward achieving a high-efficiency PSC with stable power output (low J-V hysteresis) and durability.
关键词： ZnO nanoparticles,interfacial engineering,stable perovskite solar cells,interface loss,high-efficiency perovskite solar cells,electron transport bilayer
更新于2025-11-19 16:46:39
-
2D Photonic Crystal Nanodisk Array as Electron Transport Layer for Highly Efficient Perovskite Solar Cells
摘要： Perovskite solar cells (PSCs) are currently exhibiting reproducible high efficiency; the manufacturing of low cost, scalable electron transport layers (ETLs) is becoming increasingly important. However, this remains a challenge for electron transport layers that exhibit excellent optical/electrical properties while being a thin film of simple morphology. Here we demonstrate the PSC of a 2D photonic crystal nanodisk (ND) array ETL that is compact, but greatly enhances light harvesting. The ND array is fabricated by nanosphere lithography using a monolayer of self-assembled polymer spheres as a physical mask. We fabricate ND arrays of various lattice constants simply by controlling the size of the polymer spheres. Optimal ND arrays exhibit strong forward scattering and optical confinement effects, greatly improving light harvesting in the perovskite layer. We also observe that the ND array improves charge transport by reducing contact resistance with the perovskite layer. ND array ETL PSCs reach 19% maximum power conversion efficiency, with low photocurrent-voltage hysteresis and stable photocurrent output.
关键词： optical confinement,2D photonic crystals,nanodisk array,electron transport layer,perovskite solar cells,forward scattering
更新于2025-11-19 16:46:39